Karl Schmidt Rubber Belt Infeed Conveyor — $57,500

This Karl Schmidt rubber belt infeed conveyor is available through Altitude Recycling Equipment. Karl Schmidt is a well-respected name in material handling and recycling conveyor systems, known for heavy-duty construction and long service life.

Specifications:
Manufacturer: Karl Schmidt
Belt Type: Rubber Belt
Belt Width: 60″ (approximate)
Motor: 7.5 HP
Configuration: Above Ground
Discharge Height: 16’11”
Lower Horizontal Section: 25′

About this unit:
The 60″ belt width handles high-volume material flow, and the 16’11” discharge height makes this unit well-suited for feeding into a sort line, trommel, or elevated processing equipment. The 25′ lower horizontal section provides a solid infeed run for loading material efficiently.

Above-ground configuration means no pit work required — a significant advantage for facilities looking to avoid the cost and disruption of civil work during installation.

At $57,500 this is a serious conveyor at a fraction of new replacement cost. Karl Schmidt conveyors are built to last, and units like this one are increasingly hard to find on the used market.

Contact us for photos, additional details, and logistics information.
📞 720-545-5348
✉ sales@altituderecycling.com

Altitude Recycling Equipment | Aurora, CO | Selling and sourcing recycling equipment nationwide since 2010

2020 Cross Wrap System — $199,900

This 2020 Cross Wrap System is available through Altitude Recycling Equipment — a lightly used, high-capacity wrapping system at less than half its original cost, with a significant inventory of consumable wrap film included.

Specifications:
Manufacturing Year: 2020
Commissioning Year: Late 2020 / Early 2021
Throughput: Up to 45 bales per hour
Primary Application: Solid waste, recyclables, and other commodities
Wrap Film Inventory: 13 pallets of rolls included
Hours of Use: Approximately two years of light use
Original Cost: Approximately $400,000
Asking Price: $199,900

About this unit:
Cross wrap systems encase bales in a fully wrapped film package — protecting material from moisture, contamination, and bale degradation during transport and storage. This is increasingly common in solid waste, RDF, and processed commodity operations where wrapped bales improve handling, reduce leachate, and allow outdoor or long-term storage.
This machine was manufactured in 2020, commissioned in late 2020 or early 2021, and saw approximately two years of light use before being taken out of service. At 45 bales per hour, it’s built for real production throughput — not a pilot-scale unit.
The 13 pallets of plastic wrap film included with the machine represent significant additional value. Film for cross wrap systems is a recurring consumable cost — getting over a year’s worth of film inventory bundled with the equipment purchase changes the effective economics of this deal considerably.
At $199,900 against an original cost of approximately $400,000, this is a strong entry point for an operation looking to add bale wrapping capability without a new-equipment capital commitment.

Contact us for full specs, additional photos, and logistics details.
📞 720-545-5348
✉ sales@altituderecycling.com

Altitude Recycling Equipment | Aurora, CO | Selling and sourcing recycling equipment nationwide since 2010

Can Flattener and Blower System — Model CP200 — $14,500 Each (2 Available)

Two identical CP200 can flattener and blower systems are available through Altitude Recycling Equipment. These are purpose-built systems for high-volume aluminum can processing — flattening and pneumatically conveying cans for downstream baling or storage.

Specifications:
Model: CP200
Quantity Available: 2 identical units
Flattener Motor: 7.5 HP
Blower Motor: 5 HP Heavy Duty
Conveyor Motor: ½ HP
Infeed: Cleated infeed conveyor with magnetic pulley
Throughput: Up to 2,000 lbs of whole cans per hour
Throughput: Up to 4,000 lbs of pre-flattened cans per hour
Price: $14,500 each

About these units:
The CP200 is a complete can processing system — cleated infeed conveyor with a magnetic pulley to remove ferrous contamination, a 7.5 HP flattener to reduce can volume, and a 5 HP heavy duty blower to pneumatically convey flattened cans to a downstream collection point or baler. The ½ HP conveyor ties the system together as a continuous-flow process.
At up to 2,000 lbs of whole cans per hour — or 4,000 lbs per hour of pre-flattened material — these are serious-throughput systems suited for MRFs, beverage distributors, large-scale can recyclers, and operations processing significant aluminum volume.
Both units are identical, making them a strong option for an operation looking to run parallel lines or acquire a backup unit alongside a primary system.

Contact us for condition details, additional photos, and logistics.

📞 720-545-5348
✉ sales@altituderecycling.com

Altitude Recycling Equipment | Aurora, CO | Selling and sourcing recycling equipment nationwide since 2010

Jeffrey Hammermill — Model 30WB — 60 HP — $40,500

This Jeffrey Hammermill is available through Altitude Recycling Equipment. Jeffrey Crushers & Pulverizers is one of the most established names in industrial size reduction — the 30WB is a heavy-duty hammermill built for serious, continuous-duty applications.

Specifications:

Manufacturer: Jeffrey Crushers & Pulverizers
Model: 30WB
Serial Number: 883474
Motor: 60 HP, 3-Phase
Soft Start: 75 HP Square D Soft Start Panel
Hammers: Heavy Duty 25 lb Hammers
Liner & Screen Wear: Little to none
Hammers: Never flipped
Motor: Tested
Condition: Came out running
About this unit:
The condition details on this machine are genuinely noteworthy. Little to no wear on the liners and screen, hammers that have never been flipped — these are the indicators that tell you a hammermill has had a light service life relative to its design capacity. Hammers on a machine like this are typically flipped to extend their usable life as they wear; hammers that have never been flipped means they still have full useful life ahead on both sides.

The motor has been tested and the machine came out running. The 75 HP Square D soft start panel is included — a soft start on a 60 HP hammermill protects the motor and electrical system during startup and is a meaningful value-add.

For an operation processing wood waste, pallets, organic material, or other hammer-reducible feedstocks, a low-wear Jeffrey 30WB at $40,500 is a strong acquisition.

Contact us for additional details and logistics.

📞 720-545-5348
✉ sales@altituderecycling.com

Altitude Recycling Equipment | Aurora, CO | Selling and sourcing recycling equipment nationwide since 2010

Hustler 60″ Steel Belt Infeed Conveyor — $82,500

This Hustler 60″ steel belt infeed conveyor is a heavy-duty unit built for high-volume recycling and material handling operations. With a 94 ft overall floor length and a 25 ft lower horizontal section, this conveyor is sized for large-scale MRF or transfer station applications.

Specifications:
Manufacturer: Hustler
Belt Width: 60″
Belt Type: Steel Belt
Lower Horizontal Section: 25 ft
Overall Floor Length: 94 ft
Application: Infeed / material handling

Steel belt infeed conveyors at this scale are a significant capital investment when purchased new. At $82,500 for a proven Hustler unit, this is a cost-effective option for operations looking to expand or upgrade their infeed capacity without the lead time and price tag of new equipment.

Infeed conveyors of this size are typically used in:
Single-stream MRF facilities
Paper and cardboard recycling operations
Transfer stations handling bulk recyclables
Industrial recycling programs with high daily volume

Contact us for additional photos, condition details, and logistics information. Tyler has deep experience sourcing and placing large conveyor systems and can help you evaluate fit for your facility.

📞 720-545-5348
✉ sales@altituderecycling.com
Altitude Recycling Equipment | Aurora, CO |
Selling and sourcing recycling equipment nationwide since 2010

Price: $6,500
Status: Available
Condition: Used — Just Removed from Production, Came Out Running
Specifications
Manufacturer: CP MFG
Year: 2012
Length: 18′
Belt Width: 18″
Motor: 2 HP
Power: 3 Phase / 460V
Belt: New

About This Machine
This CP MFG belt conveyor just came out of active production and was running when removed. It’s been fitted with a new belt, making it ready to drop into a new application without additional service work.
CP MFG is a well-regarded conveyor manufacturer known for durable, straightforward designs that hold up in industrial and recycling environments. At 18′ long with an 18″ belt width, this unit works well as an infeed conveyor, discharge conveyor, or line conveyor in a sorting or processing operation.
3-phase/460V power is standard in industrial settings. At $6,500 with a new belt already installed, this is strong value for a machine that was running right up until removal.

Is This Conveyor Right for Your Operation?

This conveyor is a good fit for:
Recycling facilities adding or replacing conveyor capacity
Manufacturing operations moving material between processes
MRF sorting lines needing an infeed or discharge conveyor
Distribution and fulfillment operations handling boxes or bulk material

Pricing & Contact

Asking Price: $6,500
To get more details, photos, or arrange an inspection, contact Altitude Recycling Equipment:
Call: 720-545-5348
Email: sales@altituderecycling.com
Tyler can answer technical questions and coordinate delivery.

About Altitude Recycling Equipment

Altitude Recycling Equipment has been sourcing, selling, and servicing recycling equipment since 2010. We work with businesses across Colorado, Wyoming, Utah, Nebraska, Kansas, Arizona, and New Mexico — and ship equipment and baling wire nationwide.
Looking for something not in our current inventory? Tell us what you need.

Altitude Recycling Equipment LLC | Aurora, CO | 720-545-5348 | sales@altituderecycling.com